How to crimp your own Ethernet cables (and the three tools you need)
Heads up: some links in this article are affiliate links. If you buy through them I may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. I only recommend gear I'd run myself.
TL;DR: You need three things — a crimper, connectors, and a tester — and pass-through connectors make the whole process nearly foolproof compared to the old flat crimp. Budget for a few wasted connectors while you learn; the failure mode is “doesn’t link,” not “damages anything.”
Every pre-made Ethernet cable drawer has the same problem: a pile of 3-footers, a pile of 25-footers, and never the 14-foot cable you actually need for the run you’re doing today. Once you can crimp your own, that problem disappears — you cut exactly the length you need, terminate both ends in a few minutes, and never buy a multipack “hoping one is close enough” again. It’s also just a useful skill: a bad crimp is one of the most common causes of a flaky home network, and being able to diagnose and fix it yourself beats replacing cable you don’t actually know is bad.
The three tools you need
1. A crimper (get one rated for pass-through connectors)
The crimper is the one tool worth spending slightly more on. A cheap all-plastic crimper works, but a ratcheting crimper with a proper die for pass-through 8P8C connectors gives a much more consistent result — it won’t release until the crimp is fully seated, which removes the most common beginner failure (an under-crimped connector that reads fine on a quick look but fails intermittently under flex).
A ratcheting mechanism won't release until the crimp is fully seated — the single biggest upgrade over a basic crimper.
A ratcheting RJ45 crimper ↗Look for one that also strips and cuts, so you’re not juggling a separate wire stripper and cable cutter for what should be a one-tool job.
2. Pass-through connectors (skip the old-style flat crimp)
This is the biggest quality-of-life upgrade in home networking crimping in years. A traditional RJ45 connector requires you to trim all 8 wires to exactly the same length before inserting them — get it wrong and the crimp either doesn’t seat or leaves a wire not fully contacted. A pass-through connector has channels that run all the way through the plug, so the wires poke out the front; you insert them at slightly uneven lengths, crimp, and the crimp itself trims the excess flush in the same motion. It turns “eyeball eight wires to identical length” into “shove them in until they stop.”
Buy more than you think you need — a bad first crimp is normal, and connectors are cheap.
Cat6 pass-through connectors ↗Buy connectors rated for your cable category and construction (solid vs stranded — see Cat5e vs Cat6 vs Cat6a: what actually matters at home if you haven’t picked cable yet) — a stranded-only connector on solid-core wire, or vice versa, often won’t make reliable contact even with a perfect crimp.
3. A cable tester (you cannot skip this step)
You cannot eyeball whether a crimp worked. It will often look fine and still have a pin that’s not quite seated, or two wires swapped in a pair. A cheap remote-and-main continuity tester checks every pin on both ends in a few seconds — see the best cheap network cable testers for a homelab for what to look for. Test every cable before it goes into a wall or under a desk; testing after you’ve already run it through a stud bay is a much worse afternoon.
Test every cable you crimp before it goes anywhere permanent — a bad crimp usually looks fine.
A remote+main continuity tester ↗The actual process
- Cut the length you need, plus slack. A little extra for dressing the cable and re-crimping if the first attempt fails is cheaper than cutting short.
- Strip about an inch of jacket. Most crimpers have a built-in stripper set to the right depth — don’t nick the conductors underneath, which weakens them even if the crimp still “works” that day.
- Untwist and arrange the pairs to T568B (the common home/US standard — pick one standard and use it on every cable in the house, since mixing T568A and T568B on the two ends of the same cable makes a crossover cable, which is harmless on modern auto-sensing gear but confusing to debug later).
- Insert into the pass-through connector until you can see all 8 conductors poking through the front and fully seated against the pins.
- Crimp once, firmly, with a ratcheting crimper that won’t release early. The excess wire trims off in the same squeeze.
- Test immediately, before you do anything else with the cable.
Common mistakes
- Trimming wires to length by eye on a non-pass-through connector. This is the single biggest source of first-attempt failures for beginners — it’s why pass-through connectors exist.
- Not stripping enough jacket, leaving the twisted pairs untwisted for too short a distance inside the connector, which increases crosstalk right at the termination — the one place it matters most.
- Reusing a connector. The pins deform on first crimp; a second crimp on the same connector is unreliable. They’re cheap — use a new one.
- Skipping the test “because it looks right.” It doesn’t matter how clean the crimp looks — a swapped pair or one un-seated pin is invisible without a tester and will absolutely bite you later, usually at the worst time.
- Crimping stranded connectors onto solid-core wire. The contact style is different; check the connector packaging matches your cable construction.
What to skip
- Expensive “professional” crimpers unless you’re doing this often enough to notice the difference — a mid-range ratcheting pass-through crimper covers a homelab’s entire lifetime of cable runs.
- Buying a different crimper for each connector type. One good 8P8C pass-through crimper handles Cat5e/6/6a; you don’t need a specialty tool per category.
The short version
Buy a ratcheting pass-through crimper, a bag of pass-through connectors matched to your cable, and a cheap continuity tester — in that order of importance. Pass-through connectors remove almost all the skill the old flat-crimp method demanded, and the tester is non-negotiable because a bad crimp is invisible until something tells you otherwise. Once you’ve done it twice, buying a pre-made cable in the wrong length will feel like a waste of a trip to the store.